Reports within 24 hours · Get your free instant quote
Certified Master Inspector sealCloser Look InspectorsStatewide Minnesota & IowaFree Instant Quote
Well Water Testing · Savage, MN

Water testing in Savage

Water testing for Minnesota homes, above all those on a private well. An accredited laboratory tests the water for coliform bacteria and E. coli…

Get Your Free Instant QuoteSee What's Included
Savage · Scott County

Well Water Testing in Savage

Water testing for Minnesota homes, above all those on a private well. An accredited laboratory tests the water for coliform bacteria and E. coli, nitrate, arsenic, lead, manganese, VOCs (volatile organic compounds), DRO (diesel range organics), iron, hardness, pH, fluoride, sulfate and uranium. The Minnesota Department of Health recommends testing a private well for coliform bacteria every year, nitrate every year, and arsenic and lead at least once.

Savage is a south-metro suburb of newer subdivisions on the Minnesota River bluffs. Housing here runs to newer subdivisions on the river bluffs, across the bluff-side subdivisions.

Savage is served by our Eagan team →  ·  (612) 457-1634

Well water in Scott County

MDA's 2018 township testing in Scott County covered Jackson, Louisville, Sand Creek and St. Lawrence townships, with 1.4% of the 488 tested wells (7 wells) at or over the 10 mg/L nitrate-nitrogen health standard. That is a low township-scale rate. MDH says about 10 percent of Minnesota private wells have arsenic above 10 ug/L, so it recommends one test. It lists coliform yearly, nitrate every year, and arsenic and lead at least once.

County facts checked September 2026 against: mda.state.mn.us, scottcountymn.gov, Minnesota Department of Health, Minnesota Department of Health.

Home inspection in Savage →  ·  More about well water testing →  ·  Every water test, explained →

Pairs well with:

Septic inspection in SavageRadon testing in SavageSewer scope in Savage

Water tests available in Savage

Bacteria

Shows whether surface water or waste is reaching the well.

  • Total coliform bacteria
    Surface contamination reaching the well
    None should be present (MDH)
  • E. coli
    Fecal contamination from septic, manure or wildlife
    None should be present (MDH)

Health chemicals

No taste, color or smell. These are the long-term health checks.

  • Nitrate
    Fertilizer, septic and manure; highest risk to infants
    10 mg/L (EPA)
  • Arsenic
    Natural arsenic from Minnesota rock and soil
    10 µg/L (EPA)
  • Lead
    Lead service lines, solder and brass fixtures
    No safe level (MDH)
  • Manganese
    Natural manganese; a concern for infants
    100 µg/L for infants (MDH guidance)
  • Fluoride
    Natural fluoride; dental health
    4.0 mg/L (EPA)
  • Uranium
    Natural radionuclide in groundwater
    30 µg/L (EPA)

Petroleum & solvents

Fuel and chemical spills from old tanks or nearby sites.

  • VOCs (volatile organic compounds)
    Fuels, solvents, degreasers and paints
    Varies by compound (EPA)
  • DRO (diesel range organics)
    Diesel and heating-oil petroleum
    No limit of its own; a petroleum screen (MPCA)

Household quality

Staining, scale and taste, and choosing the right treatment.

  • Iron
    Rusty staining and metallic taste
    0.3 mg/L, aesthetic (MDH)
  • Hardness
    Scale buildup; sizing a water softener
    No health standard
  • pH
    Corrosive or scaling water
    6.5 to 8.5, aesthetic (EPA)
  • Sulfate
    Taste and odor; diarrhea risk for infants
    250 mg/L, aesthetic (EPA)

Limits from MDH, EPA and MPCA. Compare your lab results with these values.

Savage private well testing timeline

Minnesota Department of Health schedule: coliform bacteria and nitrate every year, arsenic and lead at least once. Source: MDH
TestYear 1Year 2Year 3Year 4Year 5Year 6
Coliform bacteria
Nitrate
Arsenic
Lead

When to test your water

  • Every yearColiform bacteria and nitrate, the basic safety checks for a private well. Nitrate can come from fertilizer, septic systems and animal waste.
  • At least onceArsenic and lead. Arsenic can differ even between neighboring wells.
  • Before a baby drinks the waterColiform bacteria, nitrate, arsenic, lead and manganese. MDH recommends testing a private well for all five before a baby drinks the water.
  • When you buy a homeA full baseline while you can still ask questions or negotiate.
  • After flooding or well workFlooding and repairs to the well are reasons to test again.
  • When taste, color or smell changesMDH says a change in taste, smell or look is a reason to test for coliform bacteria.
  • Near a fuel tank or industrial siteVOCs, plus DRO for diesel and heating oil. MDH says to consider a VOC test if the well is near fuel tanks or a commercial or industrial area.
  • City water in an older homeLead. MDH says homes built before 1940 may have lead service lines, and plumbing parts made before 1986 may contain lead.

Based on: MDH well testing, MDH coliform bacteria, MDH nitrate, MDH water for babies, MDH flood precautions, MDH lead.

How to get it done

  1. Choose your testsPick the water testing you need in the free instant quote.
  2. Pick a timeBook online. The quote takes about 30 seconds.
  3. Get certified lab resultsA certified laboratory analyzes the water and reports each result.

Get Your Free Instant Quote

Water testing in Savage: what matters

Savage, MN water testing: well cap in the foreground, acreage with a pond behind it in rural Minnesota in summer
Nitrate: EPA limit 10 mg/L, highest risk to infants →
Well cap in the foreground, machine shed and farmhouse behind it in rural Minnesota in autumn color (Scott County, Minnesota)
Arsenic: about 10% of Minnesota wells exceed the standard →
Savage, MN water testing: well cap in the foreground, farmhouse at the end of a tree-lined drive behind it in rural Minnesota in summer
Lead: MDH says no level is safe →

Nitrate in Scott County wells

1.4%

1.4% of 488 wells tested in Jackson, Louisville, Sand Creek and St. Lawrence townships were at or over the 10 mg/L nitrate standard (MDA township testing, 2018).

Source: Minnesota Department of Agriculture township testing

Township numbers are averages. Only a test of your own well tells you its nitrate level. Get a free instant quote

How deep Savage wells go

15 ftsand and gravel (most wells)sandstone and limestone (SE and east central, incl. Twin Cities)1,000+ ft · fractured rock such as granite (NE)
Source: MDH Well Owner's Handbook

Depth and aquifer change what is in the water. Test the well you are buying, not the neighbor's. Get a free instant quote

Arsenic in Savage private wells, out of every 100

About 40 in 100 have some arsenic About 10 in 100 are above the 10 µg/L standard

Source: Minnesota Department of Health

You can't see, smell or taste arsenic. One lab test tells you where the well stands. Get a free instant quote

Questions

Common questions.

Who needs well water testing?
Any home on a private well, and above all when you are buying one. A private well is not regulated like a city water system, so the owner is responsible for knowing what is in the water. Testing before closing tells you whether the water needs treatment while you can still ask questions or negotiate.
What does the water panel cover?
The panel covers coliform bacteria and E. coli, nitrate, arsenic, lead, manganese, VOCs (volatile organic compounds), DRO (diesel range organics), iron, hardness, pH, fluoride, sulfate and uranium. Bacteria and nitrate are the short-term health checks. Arsenic, lead, manganese and uranium are the ones you cannot see or taste. VOCs and DRO screen for solvents and petroleum, such as fuel from an old oil tank or a nearby leak site. Iron, hardness, pH and sulfate explain staining, scale, odor and wear on plumbing and appliances.
How often should a well be tested?
The Minnesota Department of Health recommends coliform bacteria every year, nitrate every year, and arsenic and lead at least once. Test again after flooding, after any work on the well, or if the taste, color or smell of the water changes.
Is well water testing part of the home inspection?
It is an add-on. Add it to your home inspection quote. Testing early in your inspection window leaves time to act on the results.
What did MDA find in Scott County wells?
In 2018 initial testing of four townships (Jackson, Louisville, Sand Creek, St. Lawrence), 1.4% of the 488 wells tested were at or over the 10 mg/L nitrate health standard. MDH recommends testing for coliform bacteria every year.
My home is on city water. Is water testing still worth it?
Often yes. Community water systems follow EPA testing rules and report results in an annual Consumer Confidence Report, but that report does not measure your own plumbing. MDH and EPA say lead enters mainly from service lines and plumbing materials, and the only way to know is a tap test. MDH recommends an accredited lab, and your utility can say whether your home has a lead service line.
When should a home be tested for DRO or VOCs?
MDH suggests considering a VOC test when a well is near fuel tanks or a commercial or industrial area. MPCA reports petroleum has leaked at about 22,000 Minnesota sites, including home heating-oil tanks, and releases can threaten drinking water and send vapors into buildings. Reasons to test include a nearby leak site, a former or buried fuel tank, or a fuel odor or sheen. MPCA's leaking-tank-site database shows reported releases.
Are Savage's bluff lots a concern?
Sloped bluff lots make grading, retaining walls and walkout water entry the priorities.
What does it mean if E. coli is found in my well water?
It likely means feces, and the harmful germs they can carry, have entered the well. CDC notes most E. coli is harmless, but some types can cause serious illness, and a standard test cannot tell which type is present. Use bottled water or another safe water source.
Should I test my well for VOCs if there is a gas station nearby?
MDH says to consider testing for volatile organic chemicals if your well is near fuel tanks or a commercial or industrial area. A nearby station is a reasonable reason to ask an accredited laboratory for a VOC analysis. Results are compared with MDH health-based guidance values for each compound.
How deep are private wells in Minnesota, and what kind of aquifer do they use?
The Department of Health's Well Owner's Handbook says Minnesota wells range from 15 feet to over 1,000 feet deep. Most draw from sand and gravel deposited by glaciers. Southeastern and east central wells, including the Twin Cities area, often draw from sandstone and limestone, while northeastern wells often use fractured rock such as granite. Depth and geology vary even between neighbors, so a test of your own well is the way to know your water.
How can I tell if there is a forgotten well on my property?
The Department of Health suggests looking for a pipe 1 to 8 inches wide at, above, or below the surface, a low spot or sunken area, a metal, wood, or concrete cover, a windmill or old well house, and a concrete patch or glass block in a basement step or floor. Well pits and basement offsets are other common signs. Visible signs like these are worth raising with your agent and a licensed well contractor.
Keep looking

More across Minnesota.

Well Water Testing nearby

Other inspections in Savage

Questions about well water testing

In-depth guides

Free instant quote

Build your quote in 30 seconds.

No phone tag, no callback delay. Price and book your inspection right here — it takes about 30 seconds and there is no obligation.

Free Instant Quote & SchedulerPowered by InspectorData
Free Instant Quote